Telephone cable paper covered insulated Aluminum magnet wire strip

Paper Wrapped Aluminum wire Production Process

One step :
Take the pure aluminum material drawing into the aluminium rod wire;

Two step :
Through the extrusion production line, take the aluminum rod wire into extruding and coarse drawing operation, then becoming the requirement specification of Bare aluminium wire;

Three step :
Take up the Bare aluminum wire conductor, and inspection the bare wire coil products;

Four step :
Annealing the bare aluminum wire, and placed neatly, ready to production;

Five step :
Doing the digital dividing and cutting paper process and finished;
Pay-off the wire coil products, ready to paper covering production;

Six step :
Taking into straightening and tension lenvelling operation, ready to paper winding;

Seven step :
Taking into the paper winding operation, and then for inspecion;

Eight step :
Pulling the finished paper-covered wire, and then for take-up the wire coil , ready to packing.

Main Applications:
All kinds of household electric motors, vacuum cleaner motor, electric motor
All kinds of transformers, inductors, rectifiers
All kinds of fan motor
All kinds of high frequency electric appliance

Enameled wire is used for camcorder, electronic clock, micro relay, automobile, electronic instrument, washing machine, TV element, etc. Development direction in the diameter, use the specification range of ¦Õ0.06 ~ 0.08 mm and all thickened insulation

Question: During our production process, we found that one axis of enameled wire is wound around the axial inductance. This axis of enameled wire and other axis of enameled wire are wound on the same magnetic core. The inductance of the enameled wire with this axis is relatively high. We made 1mH inductance, and the enameled wire of the other axis was only 960uH, and the problematic wire of this axis was 1.025mH, and the inductance test frequency was 796kHz. (1) The number of stitches is the same as the number of turns, excluding the slip ring. (2) The 1-meter straight resistance is a bit smaller than that of other shafts. I personally think that the enameled wire contains magnetic substances, but if it contains magnetic substances, the resistivity should be greater, and the DC resistance should be greater. So please help to solve the problem, or have encountered this kind of problem before, please analyze it, thank you in advance!

The wrapped wire is made of natural silk, polyester fiber, glass fiber, insulating paper or synthetic resin film, etc., tightly wrapped on the conductive wire core to form an insulating layer. There are also insulating layers wrapped around the enameled wire. In addition to thin-film insulation, others such as glass filaments need to be dipped in adhesive insulating varnish to improve their electrical, mechanical and moisture-proof properties. In fact, they are combined insulation.

The enameled wire has always been a very important industry in the national economy, and with the continuous change and development of the market, the enameled wire industry is constantly adjusting, from the current perspective, the future of the entire enamel wire industry will move towards the future.

What is the difference between magnet wire and enameled wire? Enameled wire is a type of magnet wire. but most people called the magnet wire in winding wire or enameled wire. Mostly used for Inductors, transformers, reactors, dry-type transformers, cast resin transformers

The multi-shaped enamel wire refers to a metal wire for winding electromagnetic coils with an insulating paint, also known as electromagnetic wires. The multi-shaped enameled wire is the primary raw material of electrical, motor and household appliances, telecommunications, electronic external electromagnetic windings. In the future, follow the rapid development of industrial appliances, household appliances, telecommunications, electronic products, etc. Market and application fields.

In recent years, the price of electrolytic copper has continued to rise, which has brought a huge impact to the production of related copper wire raw materials and enameled wire suppliers. The use of copper-clad aluminum enameled wire has been proved by users to replace pure copper enameled wire, thus providing a huge business opportunity and a broad market for the development of my country’s enameled wire industry. The new type of Enameled Copper Coated Aluminum Magnet Wire For Voice Winding using copper clad aluminum material as the inner conductor has characteristics between copper and aluminum, combining the excellent conductivity of copper and the light weight of aluminum.

1060 Transformer Aluminum Strip Product Description:
060 transformer aluminum belt is a special purpose aluminum belt product produced for transformers. It uses high-purity aluminum substrate and aluminum deep-processed products formed by slitting aluminum coils with an aluminum content of more than 99.60%. The raw material of transformer aluminum strip is high-purity aluminum, which is rolled into thin sheet aluminum coils of different thicknesses and widths by a cold rolling mill, and then longitudinally slitted into aluminum strips of different widths by a slitting machine according to the application. It is an important raw material in industry. The main processing equipment of 1060 transformer aluminum strip is slitting unit, which can be divided into required length and width according to needs. Usually the transformer aluminum strip is slit according to the actual needs of the user, which can reduce waste, reduce processing procedures (without cutting), and save raw material costs.

The paper covered wire is a type of enameled wire that is extruded or pulled by an oxygen-free copper rod or an electrical circular aluminum rod, and then annealing the wire, and then winding two layers or two layers of insulating on the copper (aluminum) conductor.Paper (including telephone paper, cable paper, high voltage cable paper, turns], suitable for oil immersion transformer coils and other similar electrical windings.Electrical bare copper (aluminum) wires produced by extrusion process are the most ideal materials for the production of cable paper wraps.

Fiberglass Covered Insulated rectangular aluminum wire is in accordance with customer requirements in aluminum conductor uniform whole winding package 1-2 layers of alkali-free fiberglass, with the necessary temperature resistance index and compatible adhesive paint dipping and baking process, glass fiber and conductor between bonded into a whole.

The enameled wire paint coats up to 30 layers of copper and aluminum wires to provide electrical insulation and help avoid short circuits in the coil. Such enameled wire paint must also have excellent chemical resistance and high temperature resistance, must have excellent adhesion with copper or aluminum wires, and also have excellent mechanical stability.
In some cases, such as for motors driven by frequency converters, a suitable insulation layer should be able to resist partial discharges that may cause short circuits and malfunctions in the engine.

To weld the lead aluminum enameled wire, it is necessary to remove the paint (there are very few household electric fans with very low requirements, and the ballast manufacturer does not remove the paint). The paint removal methods are listed below.
(1) It can be scraped with a blade,
(2) It can be peeled with a centrifugal knife,
(3) The paint can also be rubbed off with a grinding wheel,
(4) Of course paint remover is also available,
(5) You can also use high-temperature tin to burn the paint,
(6) Some people burn with fire
(7) Of course you can also use paint remover to remove paint

The winding is the key component of the electric motor for electromagnetic energy conversion and transmission, so as to realize the conversion of electrical energy into mechanical energy. The winding is the most important part of the motor, and the choice of Enameled Copper/Aluminum Wire For Motor is also very important

According to the characteristics and uses of insulation, winding wires can be divided into four categories: enameled wires, wrapped wires, special winding wires, and inorganic composite winding wires.

Transformer oil: It is a fractionation product of petroleum, and its main components are alkanes, cycloalkane saturated hydrocarbons, aromatic unsaturated hydrocarbons and other compounds. Commonly known as square shed oil, it is a light yellow transparent liquid with a relative density of 0.895. Freezing point <-45¡æ.
Transformer oil is a kind of mineral oil obtained by distillation and refining from natural petroleum. It is a liquid natural hydrocarbon that is pure and stable, with low viscosity, good insulation, and good cooling by acid-base refining treatment of the lubricating oil fraction in petroleum. Mixture of compounds. Commonly known as square shed oil, light yellow transparent liquid.

Compared with general round wires, flat enameled wires have the following advantages:
Higher floor area ratio and better use of space: The high conductor density enables coils and components of the same size to achieve higher efficiency, save materials and reduce costs.

Submersible Winding Wire normally chooses the enameled copper wire with good performance
Longer life
Best Tensile Strength
Easy to Wind
Savings up to 25%

British Standard Wire Gauge (often abbreviated to Standard Wire Gauge or SWG) is a unit for denoting wire size given by BS 3737:1964 (now withdrawn). It is also known as the Imperial Wire Gauge or British Standard Gauge. Use of SWG sizes has fallen greatly in popularity, but they are still used as a measure of thickness in guitar strings and some electrical wire. Cross sectional area in square millimetres is now the more usual size measurement for wires used in electrical installation cables. The current British Standard for metallic materials such as wire and sheet is BS 6722:1986, which is a solely metric standard.

How to Choose your Wire Manufacturers? You want to choose competitive wire manufactuer, should think about the
Factory certificate
Wire specifications
Copper or aluminum pure

Water quality affects the production of lacquer wires?

The production water production water in the lacquered wire has a variety of uses, and like, the requirements for water quality are also different. Depending on the purpose of use, the water quality can be divided into: annealing furnace water seal water, equipment cooling water, lubricant manufacturing water, etc.

Glass-fiber covered aluminum magnet wire used to have weak coating strength (abrasion resistance, shock resistance, and flexibility). However, that disadvantage has been significantly improved recently by refining material selection and manufacturing methods. The demand for glass-fiber covered aluminum magnet wire is increasing as the wires have excellent uniformity and electrical properties under high temperatures and humidity.

Three-layer insulated wire structure
High-frequency transformer triple-insulated wire is a high-performance insulated wire, so as the name suggests, this wire has three insulation layers with a core wire in the middle.
The first layer The first layer is golden yellow polyamine film, its thickness is a few microns, but it can withstand 3KV pulse high voltage
The second layer is a spray paint coating with high insulation,
The third layer is a transparent glass fiber layer. The total thickness of the insulating layer is only 20-100um. Its advantage is high insulation strength, and any two layers can withstand a safe voltage of 3000V AC, and the current density is large.

Enameled wire is widely used in our production and life. The paint it uses is a kind of paint that can produce a good insulating layer between the wires in the winding.
Enameled wire is made on the basis of copper wire. Simply put, enameled wire is a layer of insulator on the copper wire, usually plastic. Enameled wire paint is a kind of outer layer of bare copper wire, alloy wire and glass wire covered wire of various wire diameters to improve and stabilize the performance of enameled wire. It has high mechanical strength, resistance to Freon refrigerant, good compatibility with impregnating paint, and can meet the requirements of heat resistance, impact resistance, oil resistance, etc.

Product Name:Oil Immersed Transformer Winding Wire
Type: round or rectangular wire
Features: Telephone paper, cable wire or 500KV transformer turn-to-turn insulation paper is used for insulation. After dipping.
Conductor Material:Aluminum or Copper
Application:used for Oil Immersed Transformer, transformer coils
Certificate:UL,RoHS
Thermal Class:105¡æ

1. Mechanical function: including elongation, return angle, softness and adhesion, scraping, tensile strength and other items.
2. Heat resistance: including thermal shock and softening breakdown test.
3. Electricity includes: breakdown voltage, lacquer film continuity and DC resistance test.
4. Chemical resistance includes solvent resistance and welding.

The selection criterion of the electromagnetic wire is not considered for resistance, as the problem of resistance and fever can be done by selecting the same cross-sectional wire, it is the main consideration of the thick wire or the thin wire is mainly considered Operability.

Silver plated copper wire is manufacture with the combination of silver and copper and Silver Plated Copper Electrical Wire is manufactured using grade copper and silver; the industrial standards are always kept into the consideration.

The enamel wire is a wire having an insulating layer, which is a transformation of electromagnetic energy in a winding form, also known as a winding wire.