Oxidative bare aluminium round rectangular flat magnet wire strip

Although the quality of enameled wire depends to a large extent on the quality of raw materials such as paint and wires and the objective conditions of machinery and equipment, if you do not take a series of problems such as baking, annealing, and speed, and understand their interrelationships. , Do not master the operation technology, do not seriously do the touring work, stop and tidy up the work, do not do well in the process and hygiene, even if the objective conditions are good, it will not be able to produce high-quality enameled wire. Therefore, the decisive factor for good enameled wire is people’s sense of responsibility for work.

Fiberglass Covered Aluminum Wire Production Proce

One step :
Take the pure aluminum material drawing into the aluminium rod wire;

Two step :
Through the extrusion production line, take the aluminum rod wire into extruding and coarse drawing operation, then becoming the requirement specification of Bare aluminium wire;

Three step :
Take up the Bare aluminum wire conductor, and inspection the bare wire coil products;

Four step :
Annealing the bare aluminum wire, and placed neatly, ready to production;

Five step :
Pay-off the wire coil products, ready to fiber glass covering production;

Six step :
Taking into straightening and tension levelling operation, and then for the covering fiber glass;

Seven step :
Doing the fiber-glass covering operation, and inspecion the production process;

Eight step :
Packing the fiberglass covered wire products, and placed neatly in the warehouse.

3.1 Elongation:
The standard refers to GB/T6109, inspection method: stretch the instrument
Calculation method: ratio of (length after stretching-length before stretching)/length before stretching;

3.2 Snap off:
The standard is to pull at a speed of 2 meters per second to check that the paint film is not cracked,

3.3 Round rod winding:
Wrap the enameled wires of different specifications and the corresponding copper rods around ten times to check that the paint film is not cracked. The diameter of the copper rods refers to the requirements of GB/T6109;

3.4 Thermal shock: Put the winding enameled wire in an oven (hanging in the middle of the oven) for 0.5 hours. The temperature of the oven corresponds to the specification requirements of the enameled wire. Refer to GB/T6109. After the drying, check that the paint film is not cracked.

Enameled Aluminum Wire connects Enameled Copper Wire with the short service life according to the test. The contact part of the enameled copper wire and the enameled aluminum wire will accelerate the oxidation of the aluminum wire.

Best Selling 155 Class Enamelled Copper/Aluminum Winding Wire includes copper wire and aluminum wire used for transformers, inductors, motors, generators, dry type transformer, Cast Resin Transformers. Thermal Class:Class 155, popular used for low voltage dry type transformers.

Copper Magnet Wire Manufacturing Process includes important three steps – enameling, winding and Inorganic insulated wires. Mainly introduce the method to ensure the quality of copper enameled wire.

The space factors of magnet wires are compared in the right figure. The space factors of enamelled wires are superior to those of other wires for winding, as are their electrical properties. However, more careful examination must be made of the following properties as compared with other wires.

1. Cutting
The enameled wire is composed of a conductor and an insulator, and the hardness of the two parts is very soft, so it can be cut by using a TabCUT-200 precision cutting machine with a general SiC cutting chip. Since the insulator is coated on the conductor, and its hardness and ductility are quite different, and the insulating layer has a certain degree of peeling, it is better to use some soft materials such as tin foil, rubber, etc. to wrap the cutting part when cutting. Up to prevent the insulation layer at the fracture from peeling off after cutting.

Type: insulated
Delivery time: 7-30 Days
Conductor Material: Copper
Standard: IEC,NEMA,GB,JIS
Diameter: 0.016mm–9.2mm
Brand Name: LP Magnet Wire
Bobbin: 30kg/50kg Wooden Spool

Enamelled wire stripper is specialized to depainting for transformer and electrical machine etc, and the different strippers can be chose and according to different heat resistance levels and different enamelled materials. The products include BT-112 strong enamelled wire stripper BT-105 quick enamelled wire stripper BT-101A/B stripper etc. Its characteristics BT-112 is applicable to depainting for the thrum of Copper Wire Aluminum Wire with the heat resistance level 180(H), 200(H+), 220(C). BT-105 is applicable to fast depainting for the thrum of enamelled Copper Wire Aluminum Wire with the heat resistance level 130(B), 155(F); BT-101A/B is applicable to depainting for voice coil wire EI.

The main advantages of fiberglass covered wire are:
1. The quality factor Q value is large;
2. Because it is twisted by multiple enameled wire bundles, it has good flexibility and can reduce the skin effect;
3. Because it is composed of polyurethane enameled wire, the dielectric loss angle is small, and it has direct solderability.
The disadvantage is: poor moisture resistance.

The lacquered wire is composed of two of the conductor and the insulating layer. After the bare wire is deck, after multiple painting, baking.The enameled wire can be used in transformers, motors, motors, electrical, ballasts, inductance coils, disadvantages, audio coils, microwave coils, electric fans, instrumentation, and the like.

The AWG tables are for a single, solid and round conductor. The AWG of a stranded wire is determined by the cross-sectional area of the equivalent solid conductor. Because there are also small gaps between the strands, a stranded wire will always have a slightly larger overall diameter than a solid wire with the same AWG.

Polyimide Kapton Covered Enameled Aluminum Wire Strip is a multi-layer polyimide & fluoropolymer dispersion-coated film. The fluoropolymer coating functions as a heat-fusible layer for bonding to magnet wire conductors. It has superior scrape abrasion resistance and exhibits lower frictional properties than wire insulated with other commonly used polyimide materials. Polyimide film aluminum wire is ideal for demanding magnet wire applications and for difficult-to-wind motors.

Axalta today announced that it has reached a final agreement to acquire Anhui Shengran Insulation Materials Co., Ltd. (“Anhui Shengran”). Anhui Shengran is a leading manufacturer of high-quality enameled wire paint in China. Its products are widely used in consumer electronics, electric vehicles and industrial fields. Subject to the conditions of the agreement, the transaction is expected to be completed in the second quarter of 2021. Financial terms have not been disclosed.

Compared with general round wires, flat enameled wires have the following advantages:
Higher floor area ratio and better use of space: The high conductor density enables coils and components of the same size to achieve higher efficiency, save materials and reduce costs.

Enameled wire production water also has many uses, and similarly, the requirements for water quality are also different. According to the water quality requirements of the purpose of use, it can be divided into: annealing furnace sealing water, equipment cooling water, lubricant manufacturing water, etc.

Enameled wire is a main type of magnet winding wire. It is composed of a conductor and an insulating layer. After the bare wire is softened by annealing, it is painted and baked many times. However, it is not easy to produce products that not only meet the requirements of the standard, but also meet the requirements of customers. It is affected by the quality of raw materials, process parameters, production equipment, environment and other factors. Therefore, the quality characteristics of various enameled wires are different, but they all have Mechanical properties, chemical properties, electrical properties, and thermal properties

Paper covered wire by Electrical Aluminium Pole extrusion die by a certain size or drawn wire after annealing, and then in the aluminum conductor wrapped more than two or two insulating paper (including paper, telephone, cable paper, high voltage cable paper, turn insulation paper) of the winding wire, suitable for oil-immersed transformers and other electrical winding with a similar wire. Produced by the extrusion process electrical bare aluminum wire is wrapped production of the cable wire is the best material.

Product details :
Place of origin : Henan ,China(Mainland);
Brand name : Signi;
Type : Insulated;
Conductor material : Aluminum;
Conductor type : Solid;
Insulation material : Enameled;
Diameter : 0.025-4.5mm;
Color : Natural;
Thickness : Grade 1/2/3;
Thermal Class : 130-220c;
Application : Motor,transformer,welding machine and generator;

The paint is a process of painting the paint of the enameled wire to form a uniform lacquer layer of a thickness on the metal conductor. This is related to several physical phenomena and painting methods of liquid.

1. What factors affect the softness of the enameled wire and the elongation?

The softness and elongation are good to reflect the quality of the copper quality and the enameled annealing process, and they have a big relationship for the quality of the winding.

2. What is the effect of the thickness of the paint film?

The first tasty or coated is too thick to affect aging performance. The furnace temperature control has a greater impact on aging performance.If the evaporation zone is too sharp, it has a sparp and porront on the paint film, which is poor in these places. The heat of it is high, affecting the thermal aging performance.

3. EffectWhat are the reasons for the bucket breakdown voltage?

Oxe film circle. Overseas impurities in the paint film. Curing. The thickness of the paint film

4. What are the factors affecting the thermal shock??

Influence of the kitcase process. The effect of copper wire. Influence of paint

Pay-off (link pull) ¡ú annealing ¡ú painting ¡ú baking ¡ú cooling ¡ú lubrication ¡ú take-up

In the long-term thermal aging test, three or more temperature points are usually selected for accelerated aging, commonly known as “three-point aging”.

The samples for the aging test are stranded enameled wire pairs. The production of the stranded pairs should meet the requirements of ASTM D2307 or NEMA 1000 standards, including the weight to be applied when making the stranded pairs, the number of twisted turns, the effective length of the stranded area, and The length of the two ends of the twisted pair, etc. When making a twisted pair, the required force and the number of twist turns will vary depending on the diameter of the wire. The effective length of the stranded area has nothing to do with the wire diameter, the effective length is 121¡À6 mm, and the two ends are at least 50 mm long. At least 10 twisted pairs per temperature point and mounted on twisted pair racks for high temperature aging test.

Anti-electricity-firecable wire
2. Aluminum winding wire
3. Three-layer extruded insulation wire

Generally speaking, UL certified enameled wire needs to do four tests:
Thermal Aging Test (Full Thermal Aging Test or One Temperature Thermal Aging Test)
Dielectric Strength Test
Elongation and Heat Shock Test
Infrared Analysis – IR

The structure of enameled wire is very simple, consisting of conductor and insulating layer. Because of its high dielectric strength, small footprint and good heat dissipation, it is widely used as a coil winding in motors and transformers.

Wire Enamel Coating is important used for enameled wire or magnet wire, the application is used for transformer winding coils and motor coils forming insulation to prevent short circuits.

First, my country has become the first big country of lacquer wire production and consumption. With the transfer of the world manufacturing center, the global enameled wire market has also begun to China, China has become an important processing base of the world, especially after China’s accession to WTO, my country’s enameled wire industry It also achieves rapid development, the production of enameled wires has exceeded the US and Japan, which became the world’s first production big country and consumer. As the economy is constantly increasing, the export of the downstream industry in the enameled wire has also increased year by year, and the enameled wire industry has entered the international market. The subregional aggregation is remarkable.

Aluminium Alloy Wires are made from a wide range of aluminum alloys, depending on the customer requirements. Aluminium wires are sold to manufacturers of eyelets, rivets, nails, screws and other various products. Bare Aluminium Wire is used for Cables, Junctions, Rivets, Hangers, Clips and other household Items.