Good Quality Paper Covered Flat Aluminum Enameled Copper Wire

The space factors of magnet wires are compared in the right figure. The space factors of enamelled wires are superior to those of other wires for winding, as are their electrical properties. However, more careful examination must be made of the following properties as compared with other wires.

The AWG tables are for a single, solid and round conductor. The AWG of a stranded wire is determined by the cross-sectional area of the equivalent solid conductor. Because there are also small gaps between the strands, a stranded wire will always have a slightly larger overall diameter than a solid wire with the same AWG.

ISO Certificated Polyimide Round Enamel Coated Magnet Wire has better performance than all other types of enameled wires. Polyimide paint film has only abrasion resistance slightly worse than polyester and polyvinyl acetal enameled wires. In order to improve this performance, most of the current Use polyester imide and polyamide imide to prepare enameled wire, which can increase the solid content of the paint, but the heat resistance is somewhat reduced.

Thermal Class 105 / 133 / 155 Grade Enameled Wire includes
Polyethylene formaldehyde enameled copper wire (PVF)
Polyester enameled copper wire (PEW)
Polyurethane enameled copper wire (UEW).
Application: Normally used for Oil-filled transformers, motors, micro motors, transformers and high frequency coils, relays, magnetized coils

The glass in Glass Fibre Conductor may be applied in woven tape form or as a continuous fibre. It has proved to be an efficient insulation providing coil winders with thermal stability, adequate electrical properties and good resistance to abrasion after varnishing. The glass is bonded with a varnish to improve dielectric strength and mechanical properties.

Enameled wire is the most widely used electromagnetic wire in the production of low-voltage products. A key performance requirement of this electromagnetic wire is the continuity of the paint film, which is to check the number of pinholes in the paint film under a certain length. When checking the number of pinholes, use a professional paint film continuity tester. The fewer the number of pinholes, the better the paint film integrity of the magnet wire.

Insulating paint is composed of three parts of paint base (natural or synthetic resin, asphalt, drying oil, fiber paper and its composites, etc.), solvent or diluent, and auxiliary materials (drier, pigment, emulsifier, antifungal agent, etc.) . According to the purpose, it can be divided into three types: dipping paint, covering paint and adhesive paint.

The paper covered wire is a type of enameled wire that is extruded or pulled by an oxygen-free copper rod or an electrical circular aluminum rod, and then annealing the wire, and then winding two layers or two layers of insulating on the copper (aluminum) conductor.Paper (including telephone paper, cable paper, high voltage cable paper, turns], suitable for oil immersion transformer coils and other similar electrical windings.Electrical bare copper (aluminum) wires produced by extrusion process are the most ideal materials for the production of cable paper wraps.

Heat resistance refers to the properties of a substance that can maintain its excellent physical and mechanical properties under heated conditions. The highest use temperature of commonly used materials to characterize. There are different standards and test methods for different materials. Such as plastics are generally expressed by Martin heat-resistant temperature. The coating industry uses a blast constant temperature oven or a high temperature furnace. After it reaches the specified temperature and time, the surface condition of the paint film is inspected, tested, or other properties such as impact, bending, water immersion, salt spray test, etc., and then before and after Test data representation. All coatings used in higher temperature occasions must use heat resistance as an important technical indicator of the coating film

Product Introduction :
Nomex covering corresponds to class H insulation is mainly used in the construction of condensers and capacitors. Main application of it is in shielding of cables in high temp. environments (200¡ãC) such as dry type transformers, military and aerospace cables. Nomex covered conductors are more effective in condition where temperature resistance and dielectric strength requirements are high.

By extrusion of bare aluminum wire wrapped and Nomex Paper covered wire, the mechanical performance and electrical performance better, instead of making difficult composite enameled flat wire, suitable for transformer, winding of lifting electromagnet, electric welding machine and other products.

The samples for tensile and thermal shock testing were 3 pieces of 254mm enameled wire.

First pull the enameled wire to the required elongation at a rate of 3.7-4.6 m/sec, then wrap the jerked sample around the mandrel, and then put the wrapped sample into the oven at the specified temperature for 30 minutes. It needs to be suspended in the oven. After leaving the oven, inspect the baked samples for cracking or peeling of the paint film. In this test, the diameter of the mandrel is usually 3 times the diameter of the enameled wire.

The specified temperature of the oven is set according to the temperature specified for the enameled wire of this ANSI Type in the NEMA MW1000 standard, which is usually the temperature grade of the enameled wire +20¡ãC.

Enameled round aluminum wire is made of oxygen free rod or electrical aluminum rod by a certain size of the die drawing or extrusion of the wire, the insulation paint through many times of the winding wire. Mainly used in winding of transformers, motors, generators, and various electrical devices.

1. Mechanical function: including elongation, return angle, softness and adhesion, scraping, tensile strength and other items.
2. Heat resistance: including thermal shock and softening breakdown test.
3. Electricity includes: breakdown voltage, lacquer film continuity and DC resistance test.
4. Chemical resistance includes solvent resistance and welding.

Features of Aluminum Enameled Electric Wire 1.5mm For Moxico
1) Excellent bending performance
2) High flexibility of enamel
3) Good wear resistance
4) High mechanical properties
5) Higher thermal performance
6) Good resistance to refrigerants and Freon
7) Suitable for windings subjected to continuous high temperature and mechanical stress
8) Good chemical resistance
9) Excellent mechanical and chemical properties

Winding wires used in electrical equipment are usually called magnetic wires. In other words, “magnetic wires are used to exchange electrical energy and magnetic energy.” Magnetic wire is roughly divided into enameled wire (insulation coated) and coated wire (fiber/film insulation) and their combinations. The two types of magnetic wires and their performance are very different. ASTM (American Society for Testing and Materials) B193, no more than 0.017241 ohm (square millimeter/meter), the film or coating should meet the latest version of ANSI, ASTM or NEMA applicable standards, and modify the specified resin. The modified resin is Chemically changed resin, or containing one or more additives to retain the basic chemical characteristics of the original resin to enhance certain performance or application characteristics, the coated conductor needs to meet all the required test requirements of the appropriate NEMA standard (UL certification project) .

Application
? Oil-immersed transformer windings, Dry-type transformer, High temperature transformer,
? Motor, transformer, generator, welding machine; Sealed motor, Power tools motor, Auto alternators motor, Magnet coil, High power motor, household electro motors and micro-motors;
? Medium and large electrical motor and transformer windings;
? Power substations, rectifiers, f urnace transformer oil-immersed transformer coil winding;
? Lifting electromagnet, reactors and other low-voltage and high current electromagnetic winding;
? Used in aerospace, submersible motor and high voltage coil, wind turbines, micro-electronics and so on.
Windings with light weight, high conductivity, good heat resistance; Winding used for high frequency signal transmission
Magnetic wire used in High Frequency transformer, common transformer, inductance coils, electrometers.

Enamelled Covered Aluminium Wire Production Process

One step :
Take the pure aluminum material drawing into the aluminium rod wire;

Two step :
Through the extrusion production line, take the aluminum rod wire into extruding and coarse drawing operation, then becoming the requirement specification of Bare aluminium wire;

Three step :
Take up the Bare aluminum wire conductor, and inspection the bare wire coil products;

Four step :
Trough the enameled covered production line, taking cleaning¡¢annealing and drying operation , and ready to enameled covered step;

Five step :
Taking into enameling operation, and then for cooling and lubricanting;

Six step :
Through the on-line monitoring equipment, inspecion the quality of enameled wire, and take up the fulfillment products.

Seven step :
Packing the enameled wire products, and placed neatly in warehouse.

The selection criterion of the electromagnetic wire is not considered for resistance, as the problem of resistance and fever can be done by selecting the same cross-sectional wire, it is the main consideration of the thick wire or the thin wire is mainly considered Operability.

FiberGlass covered Aluminum wire is according to customers requirement, aluminum conductor is evenly covered with one or two layers of non-alkali fiberglass, then it¡¯s impregnated in compatible insulating coating of required thermal class baked to make a whole between fiberglass and Aluminum conductor (optionally be applied to polyester and polyamide).

Submersible Winding Wire normally chooses the enameled copper wire with good performance
Longer life
Best Tensile Strength
Easy to Wind
Savings up to 25%

Wire for winding used in electrical equipment is generally called magnet wire. Simply put, ¡°Magnet wire is used for interchanging electrical energy with magnetic energy¡±.
Magnet wires are broadly divided into enamelled wire (coating insulation), covered conductor wire (fiber/film insulation), other specially formulated wire, and combinations thereof.

1060 Transformer Aluminum Strip Product Description:
060 transformer aluminum belt is a special purpose aluminum belt product produced for transformers. It uses high-purity aluminum substrate and aluminum deep-processed products formed by slitting aluminum coils with an aluminum content of more than 99.60%. The raw material of transformer aluminum strip is high-purity aluminum, which is rolled into thin sheet aluminum coils of different thicknesses and widths by a cold rolling mill, and then longitudinally slitted into aluminum strips of different widths by a slitting machine according to the application. It is an important raw material in industry. The main processing equipment of 1060 transformer aluminum strip is slitting unit, which can be divided into required length and width according to needs. Usually the transformer aluminum strip is slit according to the actual needs of the user, which can reduce waste, reduce processing procedures (without cutting), and save raw material costs.

After the product is manufactured, whether its appearance, size and performance meet the requirements of the technical standards of the product and the technical agreement of the user must be judged by the inspection beam and measured; the test shall be compared with the technical standard of the product or the technical agreement of the user and meet the requirements If it is qualified, otherwise, it is unqualified. Passing the inspection can reflect the stability of the enameled wire product quality, the material and the rationality of the process. Therefore, the quality inspection has the function of checking, preventing and identifying.

Kraft Insulated Copper Stranded Paper Covered Wire refers to the insulation layer of the wire wrapped with cable paper. The paper covered wire insulation has at least 3 layers to wrap the paper tape. When it exceeds 3 feet, the innermost and outermost layers should be covered and wrapped, and the rest can be wrapped around with a gap of no more than 2mm. When the width of the paper tape is 9.5 When mm and above, the gap should not exceed 3mm.

3.1 Elongation:
The standard refers to GB/T6109, inspection method: stretch the instrument
Calculation method: ratio of (length after stretching-length before stretching)/length before stretching;

3.2 Snap off:
The standard is to pull at a speed of 2 meters per second to check that the paint film is not cracked,

3.3 Round rod winding:
Wrap the enameled wires of different specifications and the corresponding copper rods around ten times to check that the paint film is not cracked. The diameter of the copper rods refers to the requirements of GB/T6109;

3.4 Thermal shock: Put the winding enameled wire in an oven (hanging in the middle of the oven) for 0.5 hours. The temperature of the oven corresponds to the specification requirements of the enameled wire. Refer to GB/T6109. After the drying, check that the paint film is not cracked.

Type of magnetic wire is divided into enameled wire, wrapping wire, insulated wire, combined wires and others,Mainly used in motors, electrical appliances, instruments, transformers, etc., to generate electromagnetic effects by winding coils, and use the principle of electromagnetic induction to achieve the purpose of converting electrical energy to magnetic energy

The current enamel wire industry is relatively low due to the admission threshold, and therefore the production enterprises have more and more, and the market competition is constantly intensified, but in the high-end product field, there are not many companies that can enter, in the present, and future, The enamel wire business wants to achieve better development, and build brands and scale becomes more and more important.

Direct-welding enameled wire is named after its insulating layer uses an insulating material that can be directly destroyed at 360~420¡ã, and it can be directly welded without removing the insulating layer in advance during welding. Direct welding enameled wire is currently widely used in various industries of electromagnetic coils (motors, electroacoustics, inductance, etc.). As for whether it can be used to wind the motor coil, it mainly depends on the motor power or the working environment of the coil, and there is no problem within a certain temperature range.

Oxidative Aluminum Wire (Anodized aluminium wire)belongs to the special electromagnetic wire and the insulation layer is the aluminum oxide.
Because of no thermal aging phenomenon, it can be used as insulation level of class 220.
The insulation layer of such product is thin, high temperature resistance and insulation performance stability,which is the best choice for low voltage winding wires with producing high temperature, poor environment, heat dissipation difficulty and so on.
It can widely be used in electromagnetic industries at home and abroad.

Copper Magnet Wire Manufacturing Process includes important three steps – enameling, winding and Inorganic insulated wires. Mainly introduce the method to ensure the quality of copper enameled wire.