Fiberglass Covered Insulated rectangular Aluminum Wire

Copper-clad aluminum wire refers to a wire with aluminum core wire as the main body and a certain proportion of copper layer plated on the outside. It can be used as a conductor for coaxial cables and wire and cable conductors in electrical equipment. The aluminum wire has a small specific gravity, but its welding performance is not good. Therefore, the copper-clad aluminum wire is wrapped with a copper layer on the aluminum wire. This copper-clad aluminum wire can not only take advantage of the small aluminum specific gravity, but also improve the welding performance.

The difference between enameled aluminum wire and enameled copper wire of vibration motor: the resistivity of copper wire is 0.017, and the resistivity of aluminum wire is 0.028. The cross-sectional ratio of copper wire and aluminum wire interchange is 0.79:1, and six square copper wires are equivalent to ten square aluminum wires. The diameter of the aluminum wire is thicker than that of the copper wire, and the same aluminum wire of the stator slot will not fit.

To weld the lead aluminum enameled wire, it is necessary to remove the paint (there are very few household electric fans with very low requirements, and the ballast manufacturer does not remove the paint). The paint removal methods are listed below.
(1) It can be scraped with a blade,
(2) It can be peeled with a centrifugal knife,
(3) The paint can also be rubbed off with a grinding wheel,
(4) Of course paint remover is also available,
(5) You can also use high-temperature tin to burn the paint,
(6) Some people burn with fire
(7) Of course you can also use paint remover to remove paint

The paper covered wire is a type of enameled wire that is extruded or pulled by an oxygen-free copper rod or an electrical circular aluminum rod, and then annealing the wire, and then winding two layers or two layers of insulating on the copper (aluminum) conductor.Paper (including telephone paper, cable paper, high voltage cable paper, turns], suitable for oil immersion transformer coils and other similar electrical windings.Electrical bare copper (aluminum) wires produced by extrusion process are the most ideal materials for the production of cable paper wraps.

Compared with general round wires, flat enameled wires have the following advantages:
Higher floor area ratio and better use of space: The high conductor density enables coils and components of the same size to achieve higher efficiency, save materials and reduce costs.

Direct-welding enameled wire is named after its insulating layer uses an insulating material that can be directly destroyed at 360~420¡ã, and it can be directly welded without removing the insulating layer in advance during welding. Direct welding enameled wire is currently widely used in various industries of electromagnetic coils (motors, electroacoustics, inductance, etc.). As for whether it can be used to wind the motor coil, it mainly depends on the motor power or the working environment of the coil, and there is no problem within a certain temperature range.

The winding is the key component of the electric motor for electromagnetic energy conversion and transmission, so as to realize the conversion of electrical energy into mechanical energy. The winding is the most important part of the motor, and the choice of Enameled Copper/Aluminum Wire For Motor is also very important

Enameled round aluminum wire is made of oxygen free rod or electrical aluminum rod by a certain size of the die drawing or extrusion of the wire, the insulation paint through many times of the winding wire. Mainly used in winding of transformers, motors, generators, and various electrical devices.

Brand Name: LP Magnet Wire
Certification: UL,SGS,RoHS,ISO9001
Conductor Material: copper or aluminum
Bobbin: 30kg/50kg/150kg wooden spool
Diameter: round:2.0-7.0; flat:a:1-10,b:3-35
Model Number: Paper Coated Copper Wire

Features of Aluminum Enameled Electric Wire 1.5mm For Moxico
1) Excellent bending performance
2) High flexibility of enamel
3) Good wear resistance
4) High mechanical properties
5) Higher thermal performance
6) Good resistance to refrigerants and Freon
7) Suitable for windings subjected to continuous high temperature and mechanical stress
8) Good chemical resistance
9) Excellent mechanical and chemical properties

Fiberglass Covered Insulated rectangular aluminum wire is in accordance with customer requirements in aluminum conductor uniform whole winding package 1-2 layers of alkali-free fiberglass, with the necessary temperature resistance index and compatible adhesive paint dipping and baking process, glass fiber and conductor between bonded into a whole.

High Temperature Aluminum Magnet Wire (Anodized aluminium wire) belongs to the special electromagnetic wire and the insulation layer is the aluminum oxide . Because of no thermal aging phenomenon, it can be used as insulation level of class 220.
The insulation layer of such product is thin, high temperature resistance and insulation performance stability,which is the best choice for low voltage winding wires with producing high temperature, poor environment, heat dissipation difficulty and so on.
It can widely be used in electromagnetic industries at home and abroad.

Transformer insulation wire is usually circular. Silk covered wire, also known as cotton covered wire, it is a thread or yarn on copper coated insulation materials, such as to increase the mechanical strength and dielectric strength of the wire.

The main advantages of fiberglass covered wire are:
1. The quality factor Q value is large;
2. Because it is twisted by multiple enameled wire bundles, it has good flexibility and can reduce the skin effect;
3. Because it is composed of polyurethane enameled wire, the dielectric loss angle is small, and it has direct solderability.
The disadvantage is: poor moisture resistance.

Enameled wire is coated with insulating paint on the outside of the bare Aluminium wire, constitute the inside due to the effect of insulating varnish, between the two adjacent wire can bear 200 v ac voltage Q general insulation flow line surface light, soft, can work under the condition of 130 ¡æ continuous.In addition, enameled wire bending also requires 10 times, paint should not fall off, in order to meet the winding when won’t appear the quality problem.

Aromatic polyimide enameled wire has good heat resistance, softening breakdown resistance, radiation resistance, severe cold resistance and chemical resistance. Among them, many test indicators such as unidirectional scratching, breakdown voltage, and thermal softening are far Far better than ordinary enameled wire.

¡ñ Conductor resistance. Measure with a conductor resistance tester, and then change to the value at 20¡ãC for comparison.
¡ñInsulation destruction voltage. Twist two enameled wires, apply voltage between the conductors, and judge by the damage voltage of the paint film. This performance is analyzed and judged through two tests of normal state and cold state breakdown voltage.
¡ñPaint film continuity (pinhole). Check the small holes of the paint film with a certain length of the test material. The project is tested by a high-pressure paint film continuity tester.

1. Conductor resistance ¡ª The resistance of a conductor is proportional to its length and inversely proportional to its cross-sectional area.
2. Conductivity¡ªBased on the resistance 1/58ohm (0.017241 ohm) of a standard soft copper wire with a length of 1m and a cross-sectional area of 1mm2 at 20¡æ, it is called 100% conductivity. The greater the resistance, the lower the conductivity, and the two are inversely proportional.
3. Bending resistance¡ªfix one end of the single wire, add weight to the other end to make it vertically downward, and then bend it back and forth 180 times until the wire breaks. The more bending times, the stronger the bending resistance.
4. Tensile breaking force¡ªthe maximum load weight or force applied to the specimen to break it during a tensile test.
5. Tensile strength¡ªthe breaking force per unit area to bear when the sample is broken during the tensile test.
6. Elongation ¡ª the ratio of the length of the sample after being stretched until it breaks to the original length at the specified standard distance. Conductors have different impedances at different temperatures.
Generally, 20¡ãC or 25¡ãC is the standard. The higher the temperature, the greater the impedance.

With the continuous progress of society and the continuous development of industry, enameled wire has a very broad application field and has become an indispensable main supporting raw material for products such as motors, electrical appliances, household appliances, electronics, communications and transportation, especially in recent years. The rapid development of household appliances, the advancement of electronic technology, and the rise of the communication industry have provided new space for the application of enameled wires, adjusted the application proportions in various fields, and will also put forward higher and newer technical requirements for enameled wires, and adjust enameled wires. The proportion of the structure. After joining the WTO, the enameled wire industry will face competition in the domestic and international markets, which adds a layer of thinking and pressure to corporate leaders.

The electrical insulation system for wires used in generators, electric motors, transformers, and other wire-wound electrical components is divided into different classes by temperature and temperature rise. The electrical insulation system is sometimes referred to as insulation class or thermal classification. The different classes are defined by NEMA, Underwriters Laboratories (UL), and IEC standards.

1. Polyester enameled wire (P.E.W.)
Polyester enamel-covered wire is made of heat-resistant Terephthalic Polyester resin as the main grease as the insulating film and baked on the conductor. Its characteristics are as follows:
¡ñThe heat resistance is superior to synthetic tree (P.V.F.) enameled wire and U.E.W. enameled wire.
¡ñExcellent chemical resistance (except alkaline) and solvent resistance.
¡ñThe mechanical strength is comparable to synthetic resin (P.V.F.).
¡ñThe force rate and dielectric rate are comparable to U.E.W. enameled wire.
¡ñAlkali resistance and moisture resistance are better than synthetic resin enameled wire (P.V.F).

Anti-electricity-firecable wire
2. Aluminum winding wire
3. Three-layer extruded insulation wire

In theory, any enameled wire can realize the mutual conversion between electric energy, magnetic energy and kinetic energy. However, the use of enameled wire has a processing process, and electrical products also have different working environments. Therefore, in the selection of enameled wire And when substituting, the characteristics of various enameled wires must also be considered.

Enameled Aluminum Wire – EAW
Enameled Copper Wire – ECW
Enameled Aluminum Wire VS Enameled Copper Wire

Water quality affects the production of lacquer wires?

The production water production water in the lacquered wire has a variety of uses, and like, the requirements for water quality are also different. Depending on the purpose of use, the water quality can be divided into: annealing furnace water seal water, equipment cooling water, lubricant manufacturing water, etc.

Application of China Factory Wholesale Copper Pianted Enameled Aluminum Wire
1. High frequency signal transmission
2. The preferred inner conductor material for cable television coaxial cable
3.50 RF cable, flexible RF coaxial cable inner conductor material
4. Leakage cable inner conductive material
5. Computer power supply, other data cable inner conductor material
6. Micro coaxial cable inner conductor material
7. Power transmission
8. Stranded wire
9. Power cable conductor material
10. Control cable inner conductor
11. Special cable inner conductor for automobiles and locomotives
12. Building non-wire conductor materials
13. Conductor materials such as bus bars
14. Fuse
15. Radio frequency shielding network.

ISO Certificated Polyimide Round Enamel Coated Magnet Wire has better performance than all other types of enameled wires. Polyimide paint film has only abrasion resistance slightly worse than polyester and polyvinyl acetal enameled wires. In order to improve this performance, most of the current Use polyester imide and polyamide imide to prepare enameled wire, which can increase the solid content of the paint, but the heat resistance is somewhat reduced.

Silver plated copper wire is manufacture with the combination of silver and copper and Silver Plated Copper Electrical Wire is manufactured using grade copper and silver; the industrial standards are always kept into the consideration.

Fiberglass Covered Aluminum Wire Production Proce

One step :
Take the pure aluminum material drawing into the aluminium rod wire;

Two step :
Through the extrusion production line, take the aluminum rod wire into extruding and coarse drawing operation, then becoming the requirement specification of Bare aluminium wire;

Three step :
Take up the Bare aluminum wire conductor, and inspection the bare wire coil products;

Four step :
Annealing the bare aluminum wire, and placed neatly, ready to production;

Five step :
Pay-off the wire coil products, ready to fiber glass covering production;

Six step :
Taking into straightening and tension levelling operation, and then for the covering fiber glass;

Seven step :
Doing the fiber-glass covering operation, and inspecion the production process;

Eight step :
Packing the fiberglass covered wire products, and placed neatly in the warehouse.