Copper Clad Aluminium Magnetic Wire

To weld the lead aluminum enameled wire, it is necessary to remove the paint (there are very few household electric fans with very low requirements, and the ballast manufacturer does not remove the paint). The paint removal methods are listed below.
(1) It can be scraped with a blade,
(2) It can be peeled with a centrifugal knife,
(3) The paint can also be rubbed off with a grinding wheel,
(4) Of course paint remover is also available,
(5) You can also use high-temperature tin to burn the paint,
(6) Some people burn with fire
(7) Of course you can also use paint remover to remove paint

Generally speaking, UL certified enameled wire needs to do four tests:
Thermal Aging Test (Full Thermal Aging Test or One Temperature Thermal Aging Test)
Dielectric Strength Test
Elongation and Heat Shock Test
Infrared Analysis – IR

1. Cutting
The enameled wire is composed of a conductor and an insulator, and the hardness of the two parts is very soft, so it can be cut by using a TabCUT-200 precision cutting machine with a general SiC cutting chip. Since the insulator is coated on the conductor, and its hardness and ductility are quite different, and the insulating layer has a certain degree of peeling, it is better to use some soft materials such as tin foil, rubber, etc. to wrap the cutting part when cutting. Up to prevent the insulation layer at the fracture from peeling off after cutting.

Paper Wrapped Aluminum wire Production Process

One step :
Take the pure aluminum material drawing into the aluminium rod wire;

Two step :
Through the extrusion production line, take the aluminum rod wire into extruding and coarse drawing operation, then becoming the requirement specification of Bare aluminium wire;

Three step :
Take up the Bare aluminum wire conductor, and inspection the bare wire coil products;

Four step :
Annealing the bare aluminum wire, and placed neatly, ready to production;

Five step :
Doing the digital dividing and cutting paper process and finished;
Pay-off the wire coil products, ready to paper covering production;

Six step :
Taking into straightening and tension lenvelling operation, ready to paper winding;

Seven step :
Taking into the paper winding operation, and then for inspecion;

Eight step :
Pulling the finished paper-covered wire, and then for take-up the wire coil , ready to packing.

Glass-fiber covered aluminum magnet wire used to have weak coating strength (abrasion resistance, shock resistance, and flexibility). However, that disadvantage has been significantly improved recently by refining material selection and manufacturing methods. The demand for glass-fiber covered aluminum magnet wire is increasing as the wires have excellent uniformity and electrical properties under high temperatures and humidity.

Enameled aluminum wire ,High resistance to heat shock, high temperature and good performace at softening breakdown, suitable for high-speed automated routing, able to be direct weld, with no pinhole, resistive to high frequency, wearing, refrigerants and electronics corona, high breakdown voltage

Wire for winding used in electrical equipment is generally called magnet wire. Simply put, ¡°Magnet wire is used for interchanging electrical energy with magnetic energy¡±.
Magnet wires are broadly divided into enamelled wire (coating insulation), covered conductor wire (fiber/film insulation), other specially formulated wire, and combinations thereof.

The heat resistance class of enameled wire is the ambient temperature where the enameled wire can work normally for a long time (above 20000h).

British Standard Wire Gauge (often abbreviated to Standard Wire Gauge or SWG) is a unit for denoting wire size given by BS 3737:1964 (now withdrawn). It is also known as the Imperial Wire Gauge or British Standard Gauge. Use of SWG sizes has fallen greatly in popularity, but they are still used as a measure of thickness in guitar strings and some electrical wire. Cross sectional area in square millimetres is now the more usual size measurement for wires used in electrical installation cables. The current British Standard for metallic materials such as wire and sheet is BS 6722:1986, which is a solely metric standard.

Product details :
Place of origin : Henan ,China(Mainland);
Brand name : Signi;
Type : Insulated;
Conductor material : Aluminum;
Conductor type : Solid;
Insulation material : Enameled;
Diameter : 0.025-4.5mm;
Color : Natural;
Thickness : Grade 1/2/3;
Thermal Class : 130-220c;
Application : Motor,transformer,welding machine and generator;

Compared with general round wires, flat enameled wires have the following advantages:
Higher floor area ratio and better use of space: The high conductor density enables coils and components of the same size to achieve higher efficiency, save materials and reduce costs.

We are factory specializing in the manufacture and export of enameled Coil Aluminum winding wire (EAL wire, Aluminum winding wire ) for more than three years. We have profuse designs with series quality grade, and expressly, our price is very competitive because we are manufactory, we are the source.

What is the first thing to make the enamel wire? And the manufacutring process of enameled wire is important, the extruding and baking. And the raw materials: copper conductor or aluminum conductor is enough for client’s requiremnets

Insulation description: Enamelled / Fibreglass / Nomex / Paper / Mica
Applications: high-voltage coils, relays, transformers, hand tool motors, electronic coils, etc.
Temperature resistance grade: According to the selected bottom insulation wire, there are 130, 155, 180, 200, 220 degrees and other temperature resistance grades

Heat resistance refers to the properties of a substance that can maintain its excellent physical and mechanical properties under heated conditions. The highest use temperature of commonly used materials to characterize. There are different standards and test methods for different materials. Such as plastics are generally expressed by Martin heat-resistant temperature. The coating industry uses a blast constant temperature oven or a high temperature furnace. After it reaches the specified temperature and time, the surface condition of the paint film is inspected, tested, or other properties such as impact, bending, water immersion, salt spray test, etc., and then before and after Test data representation. All coatings used in higher temperature occasions must use heat resistance as an important technical indicator of the coating film

The winding is the key component of the electric motor for electromagnetic energy conversion and transmission, so as to realize the conversion of electrical energy into mechanical energy. The winding is the most important part of the motor, and the choice of Enameled Copper/Aluminum Wire For Motor is also very important

The enameled wire has always been a very important industry in the national economy, and with the continuous change and development of the market, the enameled wire industry is constantly adjusting, from the current perspective, the future of the entire enamel wire industry will move towards the future.

Heat Level 180C Fiberglass Covered Copper Magnet Wire
Performance advantages: It has the characteristics of good voltage breakdown resistance and high mechanical strength of the insulating layer.
Product use: Mainly used for AC motors as windings.

Enameled wire is a main type of magnet winding wire. It is composed of a conductor and an insulating layer. After the bare wire is softened by annealing, it is painted and baked many times. However, it is not easy to produce products that not only meet the requirements of the standard, but also meet the requirements of customers. It is affected by the quality of raw materials, process parameters, production equipment, environment and other factors. Therefore, the quality characteristics of various enameled wires are different, but they all have Mechanical properties, chemical properties, electrical properties, and thermal properties

Best Selling 155 Class Enamelled Copper/Aluminum Winding Wire includes copper wire and aluminum wire used for transformers, inductors, motors, generators, dry type transformer, Cast Resin Transformers. Thermal Class:Class 155, popular used for low voltage dry type transformers.

The paper covered wire is a type of enameled wire that is extruded or pulled by an oxygen-free copper rod or an electrical circular aluminum rod, and then annealing the wire, and then winding two layers or two layers of insulating on the copper (aluminum) conductor.Paper (including telephone paper, cable paper, high voltage cable paper, turns], suitable for oil immersion transformer coils and other similar electrical windings.Electrical bare copper (aluminum) wires produced by extrusion process are the most ideal materials for the production of cable paper wraps.

Features of Aluminum Enameled Electric Wire 1.5mm For Moxico
1) Excellent bending performance
2) High flexibility of enamel
3) Good wear resistance
4) High mechanical properties
5) Higher thermal performance
6) Good resistance to refrigerants and Freon
7) Suitable for windings subjected to continuous high temperature and mechanical stress
8) Good chemical resistance
9) Excellent mechanical and chemical properties

Double Glass-fiber Covered Rectangular Aluminum Wire is a kind of winding wire made by electrician round aluminum rod drawn or extruded into a rectangular conductor by a certain specification die, and then a double glass fiber insulation layer is wrapped on the rectangular conductor.

Enameled wire is a type of electromagnetic wire, usually refers to the insulation wire used to make coil or winding in electrical products. It is also called the winding wire.
The electromagnetic wire must meet the requirements of various applications and manufacturing processes. The former includes its shape, specification, working at high temperature in short and long time, as well as the strong vibration and centrifugal force under high speed on certain occasions, resistance to corona and breakdown under high voltage, and chemical corrosion resistance in special atmospheres, and the requirements for tensile, bending and wear, as well as the requirements of drawing, bending and wear during winding and inlaying. Swelling and erosion during immersion and drying.

The environmental painted wires of the lacquer formula contains the shortening project development time, saving project funding, and significantly improving the quality of the project.

7 type of enameled wire in accordance with insulation materials, list the thermal class, advatanges and application per type of enameled wire. Enameled wire types also can be divided into copper magnet wire and aluminum wire in accordance with conductor.

Round Enameled Wire is one of round wire, and single wire for using electric field. The testing performance of Round Enameled Wire is important, the application of enameled wire is in accordance with different performance.

Certification: SGS,UL
Size: 0.2mm-8.0mm
Delivery time: 10-30days
Thermal Class: 130-220C
Conductor Material: Copper Clad Aluminum

An electrical motor is one kind of machine which is used to change the energy from electrical to mechanical. Most of the motors work on the principle of interaction among the electric current as well as the magnetic field within a wire winding. This can generate force in the form of shaft rotation. These motors can be powered with DC or AC sources. The DC sources are batteries whereas the AC sources are inverters, power grids, generators. A generator is mechanically similar to the motor but works in the reverse direction by converting the energy from mechanical to electrical. An electric motor can be built with the rotor, stator, air gap, windings, bearings, & commutator. The classification of motors can be done with considerations like the type of power source, construction, motion output type, and applications. This article discusses what is a motor winding, types, and its calculation.