Class 130/155/180/200/220 Pure Aluminum Enameled Wire

Resistance:
Take 1m of the enameled wire to be inspected, scrape off the paint film at both ends, measure the resistance of the enameled wire, the resistance measurement value should be within the resistance range of GB/T6109; the standard temperature is 20 degrees, the conversion formula: 20 degrees resistance/234.5+standard Temperature = actual measured resistance/234.5 + measured temperature;

Heat Level 180C Fiberglass Covered Copper Magnet Wire
Performance advantages: It has the characteristics of good voltage breakdown resistance and high mechanical strength of the insulating layer.
Product use: Mainly used for AC motors as windings.

3.1 Elongation:
The standard refers to GB/T6109, inspection method: stretch the instrument
Calculation method: ratio of (length after stretching-length before stretching)/length before stretching;

3.2 Snap off:
The standard is to pull at a speed of 2 meters per second to check that the paint film is not cracked,

3.3 Round rod winding:
Wrap the enameled wires of different specifications and the corresponding copper rods around ten times to check that the paint film is not cracked. The diameter of the copper rods refers to the requirements of GB/T6109;

3.4 Thermal shock: Put the winding enameled wire in an oven (hanging in the middle of the oven) for 0.5 hours. The temperature of the oven corresponds to the specification requirements of the enameled wire. Refer to GB/T6109. After the drying, check that the paint film is not cracked.

Copper Clad Aluminum Wire is a new enameled wire, is composed of aluminum conductor covered with copper materials, maybe self-bonding, also called self-bonding enameled wire. And the short word is ECCA.

Enameled aluminum wire ,High resistance to heat shock, high temperature and good performace at softening breakdown, suitable for high-speed automated routing, able to be direct weld, with no pinhole, resistive to high frequency, wearing, refrigerants and electronics corona, high breakdown voltage

Wire for winding used in electrical equipment is generally called magnet wire. Simply put, ¡°Magnet wire is used for interchanging electrical energy with magnetic energy¡±.
Magnet wires are broadly divided into enamelled wire (coating insulation), covered conductor wire (fiber/film insulation), other specially formulated wire, and combinations thereof.

List 5 type of enameled wire characteristics
Acetal enameled wire
Polyurethane enameled wire
Polyester and modified polyester enameled wire
Polyesterimide/polyamide imide composite enameled wire
Polyesterimide/polyamide composite enameled wire

Round Enameled Wire can be designed in 0.016-7mm, why choose the round enameled wire used for your electrical equipment and other electric field. List the 4 characteristics of enameled copper wire.

Winding wires used in electrical equipment are usually called magnetic wires. In other words, “magnetic wires are used to exchange electrical energy and magnetic energy.” Magnetic wire is roughly divided into enameled wire (insulation coated) and coated wire (fiber/film insulation) and their combinations. The two types of magnetic wires and their performance are very different. ASTM (American Society for Testing and Materials) B193, no more than 0.017241 ohm (square millimeter/meter), the film or coating should meet the latest version of ANSI, ASTM or NEMA applicable standards, and modify the specified resin. The modified resin is Chemically changed resin, or containing one or more additives to retain the basic chemical characteristics of the original resin to enhance certain performance or application characteristics, the coated conductor needs to meet all the required test requirements of the appropriate NEMA standard (UL certification project) .

Electromagnetic wires used to make motor windings can basically be divided into two categories: enameled wires and wound wires, in addition to inorganic insulated electromagnetic wires. Improve the electrical and mechanical properties of the magnet wire, improve its solvent resistance, heat resistance, and reduce the thickness of the insulation, which can greatly increase the slot full rate of the motor. The slot full rate is the ratio of the total cross-section of the conductor in a slot of the motor to the cross-sectional area of ??the slot, or the filling factor of the slot. This value is of great significance for reducing the volume and weight of the motor.

Transformer insulation wire is usually circular. Silk covered wire, also known as cotton covered wire, it is a thread or yarn on copper coated insulation materials, such as to increase the mechanical strength and dielectric strength of the wire.

ENAMELED ROUND ALUMINUM WINDING WIRES are widely used for Oil-immersed transformer windings, Dry-type transformer, High temperature transformer, Motor, transformer, generator, welding machine; Sealed motor, Power tools motor, Auto alternators motor, Magnet coil, High power motor, household electro motors and micro-motors;

Enameled round aluminum wire is made of oxygen free rod or electrical aluminum rod by a certain size of the die drawing or extrusion of the wire, the insulation paint through many times of the winding wire. Mainly used in winding of transformers, motors, generators, and various electrical devices.

Round Enameled Wire type: Aluminum Wire and Copper Wire
Application:used for transformers, inductors, motors, generators, dry type transformer, Cast Resin Transformers
Dimension: Aluminum : 0.2-9.2mm; Copper: 0.016-7mm

The coating is a process of forming a uniform coating layer of a coating wire to form a uniform coating layer on a metal conductor. This is related to some physical phenomena and painting methods of liquid.

The temperature resistance of composite enameled wire can reach above 520 degrees.
Composite enameled wire is an ideal wrapping wire for large-scale low-voltage and high-current electrical appliances such as power oil-immersed, dry-type, special transformers, electric welding machines, reactor rectifiers, electromagnetic separators, etc., with excellent electrical performance and stability.

The wrapped wire is made of natural silk, polyester fiber, glass fiber, insulating paper or synthetic resin film, etc., tightly wrapped on the conductive wire core to form an insulating layer. There are also insulating layers wrapped around the enameled wire. In addition to thin-film insulation, others such as glass filaments need to be dipped in adhesive insulating varnish to improve their electrical, mechanical and moisture-proof properties. In fact, they are combined insulation.

Copper paint package wire production process principle

Copper lacquer wires are coated with respective lacquer solutions, and then cured by solvent volatilization and paint film.The earliest enamel wire is oily painted wire, made from tung oil.Its paint film is abrasion resistant, and cannot be used directly to make motor coils and windings, and the cotton yarn can be added to the layer.Later, polyethylene glycol formaldehyde lacquer wire came out, and its mechanical properties were greatly improved, which can be used directly for motor windings, which is called high-strength enameled wire.

The main advantage of the TIW wires is relatively high electric strength of the insulation, with breakdown voltage min. 6kV. Obtaining such a high resistance was possible by the use of a reinforced, three-layer conductor insulation. Third external insulation made of polyamide gives excellent flexibility and high mechanical resistance of the wire. Normally, TIW wires are produced in thermal class B. Fully automated manufacturing process provides a central position of conductor and the same thickness of insulation at any point of the wire.

Application
? Oil-immersed transformer windings, Dry-type transformer, High temperature transformer,
? Motor, transformer, generator, welding machine; Sealed motor, Power tools motor, Auto alternators motor, Magnet coil, High power motor, household electro motors and micro-motors;
? Medium and large electrical motor and transformer windings;
? Power substations, rectifiers, f urnace transformer oil-immersed transformer coil winding;
? Lifting electromagnet, reactors and other low-voltage and high current electromagnetic winding;
? Used in aerospace, submersible motor and high voltage coil, wind turbines, micro-electronics and so on.
Windings with light weight, high conductivity, good heat resistance; Winding used for high frequency signal transmission
Magnetic wire used in High Frequency transformer, common transformer, inductance coils, electrometers.

Enameled Aluminum Wire – EAW
Enameled Copper Wire – ECW
Enameled Aluminum Wire VS Enameled Copper Wire

1. What factors affect the softness of the enameled wire and the elongation?

The softness and elongation are good to reflect the quality of the copper quality and the enameled annealing process, and they have a big relationship for the quality of the winding.

2. What is the effect of the thickness of the paint film?

The first tasty or coated is too thick to affect aging performance. The furnace temperature control has a greater impact on aging performance.If the evaporation zone is too sharp, it has a sparp and porront on the paint film, which is poor in these places. The heat of it is high, affecting the thermal aging performance.

3. EffectWhat are the reasons for the bucket breakdown voltage?

Oxe film circle. Overseas impurities in the paint film. Curing. The thickness of the paint film

4. What are the factors affecting the thermal shock??

Influence of the kitcase process. The effect of copper wire. Influence of paint

The samples for the dielectric strength test are also twisted pairs, and the number is 5 pairs. During the test, the voltage was applied at a boosting rate of 500V/S until breakdown, and the voltage at the time of breakdown was recorded. The requirements for dielectric strength in the NEMA MW1000 standard will vary according to different wire diameters, different paint film thicknesses, and different enameled wire types.

Insulating paint is composed of three parts of paint base (natural or synthetic resin, asphalt, drying oil, fiber paper and its composites, etc.), solvent or diluent, and auxiliary materials (drier, pigment, emulsifier, antifungal agent, etc.) . According to the purpose, it can be divided into three types: dipping paint, covering paint and adhesive paint.

1. Different materials: structure and composition are different
2. Different performance: Since the three-layer insulated wire cannot be directly welded, it needs to be stripped first, and the cost is higher, and it will be replaced by FIW; the insulation level is different, and the three-layer insulated wire can be produced with a temperature resistance of 200 degrees
3. Can be different in color, etc.

Compared with general round wires, flat enameled wires have the following advantages:
Higher floor area ratio and better use of space: The high conductor density enables coils and components of the same size to achieve higher efficiency, save materials and reduce costs.

Nomex covering corresponds to class H insulation is mainly used in the construction of condensers and capacitors. Main application of it is in shielding of cables in high temp. environments (200¡ãC) such as dry type transformers, military and aerospace cables. Nomex covered conductors are more effective in condition where temperature resistance and dielectric strength requirements are high.
Application of Nomex Paper Covered Aluminum wire :
Mobile Transformer,Traction Transfomers,Pole-mounted distribution transformers,Power substantions,rectifiers,oil-immersed transfomer coil winding.

These Paper wrapped insulated aluminium wires enamelled and Strips are made from very high quality raw material which ensures hassle free work performance at its user end. These Paper Covered Aluminum Wires and Strips are technologically advanced and confirm to industrial quality norms of international standard. These Paper Covered Aluminum Wires and Strips are widely finds its applications in various industrial sectors.

1. Conductor resistance ¡ª The resistance of a conductor is proportional to its length and inversely proportional to its cross-sectional area.
2. Conductivity¡ªBased on the resistance 1/58ohm (0.017241 ohm) of a standard soft copper wire with a length of 1m and a cross-sectional area of 1mm2 at 20¡æ, it is called 100% conductivity. The greater the resistance, the lower the conductivity, and the two are inversely proportional.
3. Bending resistance¡ªfix one end of the single wire, add weight to the other end to make it vertically downward, and then bend it back and forth 180 times until the wire breaks. The more bending times, the stronger the bending resistance.
4. Tensile breaking force¡ªthe maximum load weight or force applied to the specimen to break it during a tensile test.
5. Tensile strength¡ªthe breaking force per unit area to bear when the sample is broken during the tensile test.
6. Elongation ¡ª the ratio of the length of the sample after being stretched until it breaks to the original length at the specified standard distance. Conductors have different impedances at different temperatures.
Generally, 20¡ãC or 25¡ãC is the standard. The higher the temperature, the greater the impedance.