China Factory Wholesale Copper Pianted Enameled Aluminum Wire

The selection criterion of the electromagnetic wire is not considered for resistance, as the problem of resistance and fever can be done by selecting the same cross-sectional wire, it is the main consideration of the thick wire or the thin wire is mainly considered Operability.

Copper Magnet Wire Manufacturing Process includes important three steps – enameling, winding and Inorganic insulated wires. Mainly introduce the method to ensure the quality of copper enameled wire.

¡ñ Conductor resistance. Measure with a conductor resistance tester, and then change to the value at 20¡ãC for comparison.
¡ñInsulation destruction voltage. Twist two enameled wires, apply voltage between the conductors, and judge by the damage voltage of the paint film. This performance is analyzed and judged through two tests of normal state and cold state breakdown voltage.
¡ñPaint film continuity (pinhole). Check the small holes of the paint film with a certain length of the test material. The project is tested by a high-pressure paint film continuity tester.

1. Conductor resistance ¡ª The resistance of a conductor is proportional to its length and inversely proportional to its cross-sectional area.
2. Conductivity¡ªBased on the resistance 1/58ohm (0.017241 ohm) of a standard soft copper wire with a length of 1m and a cross-sectional area of 1mm2 at 20¡æ, it is called 100% conductivity. The greater the resistance, the lower the conductivity, and the two are inversely proportional.
3. Bending resistance¡ªfix one end of the single wire, add weight to the other end to make it vertically downward, and then bend it back and forth 180 times until the wire breaks. The more bending times, the stronger the bending resistance.
4. Tensile breaking force¡ªthe maximum load weight or force applied to the specimen to break it during a tensile test.
5. Tensile strength¡ªthe breaking force per unit area to bear when the sample is broken during the tensile test.
6. Elongation ¡ª the ratio of the length of the sample after being stretched until it breaks to the original length at the specified standard distance. Conductors have different impedances at different temperatures.
Generally, 20¡ãC or 25¡ãC is the standard. The higher the temperature, the greater the impedance.

How to Choose your Wire Manufacturers? You want to choose competitive wire manufactuer, should think about the
Factory certificate
Wire specifications
Copper or aluminum pure

Submersible Winding Wire normally chooses the enameled copper wire with good performance
Longer life
Best Tensile Strength
Easy to Wind
Savings up to 25%

1. What factors affect the softness of the enameled wire and the elongation?

The softness and elongation are good to reflect the quality of the copper quality and the enameled annealing process, and they have a big relationship for the quality of the winding.

2. What is the effect of the thickness of the paint film?

The first tasty or coated is too thick to affect aging performance. The furnace temperature control has a greater impact on aging performance.If the evaporation zone is too sharp, it has a sparp and porront on the paint film, which is poor in these places. The heat of it is high, affecting the thermal aging performance.

3. EffectWhat are the reasons for the bucket breakdown voltage?

Oxe film circle. Overseas impurities in the paint film. Curing. The thickness of the paint film

4. What are the factors affecting the thermal shock??

Influence of the kitcase process. The effect of copper wire. Influence of paint

British Standard Wire Gauge (often abbreviated to Standard Wire Gauge or SWG) is a unit for denoting wire size given by BS 3737:1964 (now withdrawn). It is also known as the Imperial Wire Gauge or British Standard Gauge. Use of SWG sizes has fallen greatly in popularity, but they are still used as a measure of thickness in guitar strings and some electrical wire. Cross sectional area in square millimetres is now the more usual size measurement for wires used in electrical installation cables. The current British Standard for metallic materials such as wire and sheet is BS 6722:1986, which is a solely metric standard.

Kapton insulated aluminium wires are suitable for both HV and UHV applications at temperatures ranging from -269 to 200¡ãC with maximum bakeout temperature of 260¡ãC.
Kapton insulated aluminum wire is designed for use in high & ultra-high vacuum applications. Kapton has high mechanical strength, excellent electrical insulation properties, and low outgassing rates making it ideal for use as an in-vacuum insulator. These wires can be utilized in temperature ranges from 4K to 260¡ãC.

Product Name:Oil Immersed Transformer Winding Wire
Type: round or rectangular wire
Features: Telephone paper, cable wire or 500KV transformer turn-to-turn insulation paper is used for insulation. After dipping.
Conductor Material:Aluminum or Copper
Application:used for Oil Immersed Transformer, transformer coils
Certificate:UL,RoHS
Thermal Class:105¡æ

The difference between enameled aluminum wire and enameled copper wire of vibration motor: the resistivity of copper wire is 0.017, and the resistivity of aluminum wire is 0.028. The cross-sectional ratio of copper wire and aluminum wire interchange is 0.79:1, and six square copper wires are equivalent to ten square aluminum wires. The diameter of the aluminum wire is thicker than that of the copper wire, and the same aluminum wire of the stator slot will not fit.

The coating is a process of forming a uniform coating layer of a coating wire to form a uniform coating layer on a metal conductor. This is related to some physical phenomena and painting methods of liquid.

Application of enamel coated magnet wire
Wire for winding used in electrical equipment is generally called magnet wire. Simplyput,”enamel coated magnet wire is used for interchanging electrical energy with magnetic energy”.Magnet wires are broadly divided into enamelled wire (coating insulation), coveredconductor wire (fiber/film insulation), and combinations thereof.

Type of magnetic wire is divided into enameled wire, wrapping wire, insulated wire, combined wires and others,Mainly used in motors, electrical appliances, instruments, transformers, etc., to generate electromagnetic effects by winding coils, and use the principle of electromagnetic induction to achieve the purpose of converting electrical energy to magnetic energy

1. Mechanical function: including elongation, return angle, softness and adhesion, scraping, tensile strength and other items.
2. Heat resistance: including thermal shock and softening breakdown test.
3. Electricity includes: breakdown voltage, lacquer film continuity and DC resistance test.
4. Chemical resistance includes solvent resistance and welding.

Enameled wires are widely used in industrial production, household appliances and other industries. The main properties and uses of various enameled wires are as follows: Various machines, communication equipment, meters, relays, small transformers, etc.

Aluminium Alloy Wires are made from a wide range of aluminum alloys, depending on the customer requirements. Aluminium wires are sold to manufacturers of eyelets, rivets, nails, screws and other various products. Bare Aluminium Wire is used for Cables, Junctions, Rivets, Hangers, Clips and other household Items.

Round Enameled Wire type: Aluminum Wire and Copper Wire
Application:used for transformers, inductors, motors, generators, dry type transformer, Cast Resin Transformers
Dimension: Aluminum : 0.2-9.2mm; Copper: 0.016-7mm

Fiberglass Covered Aluminum Wire Production Proce

One step :
Take the pure aluminum material drawing into the aluminium rod wire;

Two step :
Through the extrusion production line, take the aluminum rod wire into extruding and coarse drawing operation, then becoming the requirement specification of Bare aluminium wire;

Three step :
Take up the Bare aluminum wire conductor, and inspection the bare wire coil products;

Four step :
Annealing the bare aluminum wire, and placed neatly, ready to production;

Five step :
Pay-off the wire coil products, ready to fiber glass covering production;

Six step :
Taking into straightening and tension levelling operation, and then for the covering fiber glass;

Seven step :
Doing the fiber-glass covering operation, and inspecion the production process;

Eight step :
Packing the fiberglass covered wire products, and placed neatly in the warehouse.

The enameled wire has always been a very important industry in the national economy, and with the continuous change and development of the market, the enameled wire industry is constantly adjusting, from the current perspective, the future of the entire enamel wire industry will move towards the future.

According to SMM survey data, the operating rate of enameled wire in September was 71.32%, down 8.28% year-on-year, down 1.82% month-on-month, and 1.65% lower than the expected 72.97%. Among them, the operating rate of large enterprises was 71.56%, down 0.69% from the previous month; medium-sized enterprises fell by 4.06% to 71.50%, and small enterprises fell by 0.55% to 60.83%.

The samples for the dielectric strength test are also twisted pairs, and the number is 5 pairs. During the test, the voltage was applied at a boosting rate of 500V/S until breakdown, and the voltage at the time of breakdown was recorded. The requirements for dielectric strength in the NEMA MW1000 standard will vary according to different wire diameters, different paint film thicknesses, and different enameled wire types.

The paint is a process of painting the paint of the enameled wire to form a uniform lacquer layer of a thickness on the metal conductor. This is related to several physical phenomena and painting methods of liquid.

Features of Aluminum Enameled Electric Wire 1.5mm For Moxico
1) Excellent bending performance
2) High flexibility of enamel
3) Good wear resistance
4) High mechanical properties
5) Higher thermal performance
6) Good resistance to refrigerants and Freon
7) Suitable for windings subjected to continuous high temperature and mechanical stress
8) Good chemical resistance
9) Excellent mechanical and chemical properties

Paper insulation enameled transposition conductor characteristics:
1. There is no circulating current, the eddy current loss in the coil is small, and the current density can be improved;
2. Simplify the winding process;
3. The full rate is higher than that of the paper-covered wire slot.

Paper-insulated enameled transposed wires are mainly used in the coils of large transformers.

enameled aluminum wire is composed of aluminum conductor and insulation materials, which is insulated with a thin film or coating and creates a magnetic field when the wire is would in a coil and power is applied. Aluminum Conductor is main type of enameled wire.

The samples for tensile and thermal shock testing were 3 pieces of 254mm enameled wire.

First pull the enameled wire to the required elongation at a rate of 3.7-4.6 m/sec, then wrap the jerked sample around the mandrel, and then put the wrapped sample into the oven at the specified temperature for 30 minutes. It needs to be suspended in the oven. After leaving the oven, inspect the baked samples for cracking or peeling of the paint film. In this test, the diameter of the mandrel is usually 3 times the diameter of the enameled wire.

The specified temperature of the oven is set according to the temperature specified for the enameled wire of this ANSI Type in the NEMA MW1000 standard, which is usually the temperature grade of the enameled wire +20¡ãC.

Telephone cable is usually thought of only as a communication medium operating at a normal 48 Vdc level. But telephone cable is regularly used by telephone operating companies to supply power to remote telephony equipment such as: PCM (Pulse Code Modulation) repeaters, FDM (Frequency Division Modulation) repeaters, telegraph and various types of control circuits. The normal talk battery voltage is regularly exceeded in the case of long subscriber loops utilizing loop extenders and on dial long line circuits which operate in the 70 to 100 Vdc range. For these applications, the referenced devices are generally current limited to approximately 150 milliamps. In all such cases, normal telephone industry practice usually limits pair-toground applied voltage to 150 Vdc, and pair-to-pair voltage is usually limited to 300 Vdc.

Anti-electricity-firecable wire
2. Aluminum winding wire
3. Three-layer extruded insulation wire

Enameled wire
The insulation of enameled wire is varnish film, which is formed by coating insulating varnish on the conductive wire core and drying it.

Product features and uses
The paint film of the enameled wire is uniform and smooth, which is conducive to the automatic winding of the coil; the paint film is also thin, which is conducive to improving the space factor, and is widely used in small and medium-sized or micro electrical products