Briefly describe the opportunities facing the enameled wire industry

Thermal Class: 130-220C
Conductor Material: Copper
Standard: IEC,NEMA,GB,JIS
Delivery time: 7-30 Days
Brand Name: LP Magnet Wire
Insulation: PEW, PIW, EIW, AIW, EI/AIW

Fiberglass Covered Insulated rectangular aluminum wire is in accordance with customer requirements in aluminum conductor uniform whole winding package 1-2 layers of alkali-free fiberglass, with the necessary temperature resistance index and compatible adhesive paint dipping and baking process, glass fiber and conductor between bonded into a whole.

The paper covered wire is a type of enameled wire that is extruded or pulled by an oxygen-free copper rod or an electrical circular aluminum rod, and then annealing the wire, and then winding two layers or two layers of insulating on the copper (aluminum) conductor.Paper (including telephone paper, cable paper, high voltage cable paper, turns], suitable for oil immersion transformer coils and other similar electrical windings.Electrical bare copper (aluminum) wires produced by extrusion process are the most ideal materials for the production of cable paper wraps.

The heat resistance class of enameled wire is the ambient temperature where the enameled wire can work normally for a long time (above 20000h).

Water quality affects the production of lacquer wires?

The production water production water in the lacquered wire has a variety of uses, and like, the requirements for water quality are also different. Depending on the purpose of use, the water quality can be divided into: annealing furnace water seal water, equipment cooling water, lubricant manufacturing water, etc.

Question: During our production process, we found that one axis of enameled wire is wound around the axial inductance. This axis of enameled wire and other axis of enameled wire are wound on the same magnetic core. The inductance of the enameled wire with this axis is relatively high. We made 1mH inductance, and the enameled wire of the other axis was only 960uH, and the problematic wire of this axis was 1.025mH, and the inductance test frequency was 796kHz. (1) The number of stitches is the same as the number of turns, excluding the slip ring. (2) The 1-meter straight resistance is a bit smaller than that of other shafts. I personally think that the enameled wire contains magnetic substances, but if it contains magnetic substances, the resistivity should be greater, and the DC resistance should be greater. So please help to solve the problem, or have encountered this kind of problem before, please analyze it, thank you in advance!

Aluminium Alloy Wires are made from a wide range of aluminum alloys, depending on the customer requirements. Aluminium wires are sold to manufacturers of eyelets, rivets, nails, screws and other various products. Bare Aluminium Wire is used for Cables, Junctions, Rivets, Hangers, Clips and other household Items.

The samples for the dielectric strength test are also twisted pairs, and the number is 5 pairs. During the test, the voltage was applied at a boosting rate of 500V/S until breakdown, and the voltage at the time of breakdown was recorded. The requirements for dielectric strength in the NEMA MW1000 standard will vary according to different wire diameters, different paint film thicknesses, and different enameled wire types.

With the continuous progress of society and the continuous development of industry, enameled wire has a very broad application field and has become an indispensable main supporting raw material for products such as motors, electrical appliances, household appliances, electronics, communications and transportation, especially in recent years. The rapid development of household appliances, the advancement of electronic technology, and the rise of the communication industry have provided new space for the application of enameled wires, adjusted the application proportions in various fields, and will also put forward higher and newer technical requirements for enameled wires, and adjust enameled wires. The proportion of the structure. After joining the WTO, the enameled wire industry will face competition in the domestic and international markets, which adds a layer of thinking and pressure to corporate leaders.

The wire drawing metal processing technology can form fine lines on the surface of the metal material, which makes the metal more textured, and is used as a decoration by users and is well-loved. In the production process, the drawing lubricating fluid is indispensable in the drawing metal processing technology. It is widely used in the lubrication of the middle drawing, small drawing and micro drawing of enameled copper wire. So how to choose this kind of drawing fluid?

Electrical wiring to be run in conduit comes in individual strands, encased in insulation to protect the wire and insulate it from other wires and the conduit. Wires come in ither solid or stranded, depending on the wire size. Bare conductors are available for ground wires only. The insulation is made to take on some rather extreme conditions. Heat-, oil-, gasoline- and water-resistant coatings are all available to help your Insulated electric wire survive.

The lacquered wire is composed of two of the conductor and the insulating layer. After the bare wire is deck, after multiple painting, baking.The enameled wire can be used in transformers, motors, motors, electrical, ballasts, inductance coils, disadvantages, audio coils, microwave coils, electric fans, instrumentation, and the like.

The temperature resistance index of Class 155 Reasonable Price Glass Fiber Covered Aluminum Round Wire has three grades: 130, 155, and 180, and the insulation thickness generally has four grades of 20, 30, 40, and 50. This product is widely used in windings of transformers, electromagnets, welding machines or other similar electrical equipment products. Electrician bare aluminum wire produced by extrusion process is the most ideal material for producing glass fiber coated aluminum wire.

Enameled wire is a main type of winding wire. It is made of a metal conductor as a conductive inner core and coated with a polymer insulating layer. It is mainly composed of these two parts; it is the conversion of electromagnetic energy into mechanical energy, heat energy, sound energy, light energy or machinery Functional materials that convert energies such as heat, heat, chemistry, sound and light into electromagnetic energy.

Painted wire (electromagnetic wire) is the base and key material of the motor, electrical, household appliance, electronics, instrumentation, electromagnetic windings. With the rapid development of my country’s home appliance industry, electronic information, automobile and other industries, the scale of electromagnetic wire production enterprises expanded, and the country has developed from thousands of tons to the 10,000-tonnes. The rapid development of industrial appliances, household appliances, automotive and other industries, bringing electromagnetic wires and markets, but at the same time, rapid advancement of technology has made a growing demand for electromagnetic wires.

Although the quality of enameled wire depends to a large extent on the quality of raw materials such as paint and wires and the objective conditions of machinery and equipment, if you do not take a series of problems such as baking, annealing, and speed, and understand their interrelationships. , Do not master the operation technology, do not seriously do the touring work, stop and tidy up the work, do not do well in the process and hygiene, even if the objective conditions are good, it will not be able to produce high-quality enameled wire. Therefore, the decisive factor for good enameled wire is people’s sense of responsibility for work.

3.1 Elongation:
The standard refers to GB/T6109, inspection method: stretch the instrument
Calculation method: ratio of (length after stretching-length before stretching)/length before stretching;

3.2 Snap off:
The standard is to pull at a speed of 2 meters per second to check that the paint film is not cracked,

3.3 Round rod winding:
Wrap the enameled wires of different specifications and the corresponding copper rods around ten times to check that the paint film is not cracked. The diameter of the copper rods refers to the requirements of GB/T6109;

3.4 Thermal shock: Put the winding enameled wire in an oven (hanging in the middle of the oven) for 0.5 hours. The temperature of the oven corresponds to the specification requirements of the enameled wire. Refer to GB/T6109. After the drying, check that the paint film is not cracked.

Magnet wire is an insulated wire used to make coils or windings in electrical products. Also called winding wire. Magnet wires must meet the requirements of a variety of uses and manufacturing processes. The former includes its shape, size, ability to work at high temperatures for short and long periods of time, as well as withstanding strong vibration and centrifugal force at high speeds in some occasions, resistance to corona and breakdown under high voltage, and resistance to chemicals in special atmospheres Corrosion, etc.; the latter includes the requirements of stretching, bending and abrasion during winding and embedding, as well as swelling and erosion during dipping and drying.

Carbon aluminum wire is an aluminum wire for parts manufacturing of various machines.08 and 08F aluminum wire for rolling thin plates, deep-drawing products, oil drums, high-grade enamel products, less demanding carburizing and cyanide parts, welding rods, etc.

Telephone cable is usually thought of only as a communication medium operating at a normal 48 Vdc level. But telephone cable is regularly used by telephone operating companies to supply power to remote telephony equipment such as: PCM (Pulse Code Modulation) repeaters, FDM (Frequency Division Modulation) repeaters, telegraph and various types of control circuits. The normal talk battery voltage is regularly exceeded in the case of long subscriber loops utilizing loop extenders and on dial long line circuits which operate in the 70 to 100 Vdc range. For these applications, the referenced devices are generally current limited to approximately 150 milliamps. In all such cases, normal telephone industry practice usually limits pair-toground applied voltage to 150 Vdc, and pair-to-pair voltage is usually limited to 300 Vdc.

Thermal Class 105 / 133 / 155 Grade Enameled Wire includes
Polyethylene formaldehyde enameled copper wire (PVF)
Polyester enameled copper wire (PEW)
Polyurethane enameled copper wire (UEW).
Application: Normally used for Oil-filled transformers, motors, micro motors, transformers and high frequency coils, relays, magnetized coils

Enameled wire motors, electrical appliances, home appliances, communications, electronic information, instrumentation, power tools, automobiles and other industries provide supporting basic material industries. They are the main and key raw materials for electromagnetic windings of motors and electronic instruments. The rapid development of electronic products, etc., has brought a broader application field and market to enameled wires, but at the same time, higher requirements have been put forward for enameled wires, and enameled wires have continued to develop towards a high level and high quality.

An electrical motor is one kind of machine which is used to change the energy from electrical to mechanical. Most of the motors work on the principle of interaction among the electric current as well as the magnetic field within a wire winding. This can generate force in the form of shaft rotation. These motors can be powered with DC or AC sources. The DC sources are batteries whereas the AC sources are inverters, power grids, generators. A generator is mechanically similar to the motor but works in the reverse direction by converting the energy from mechanical to electrical. An electric motor can be built with the rotor, stator, air gap, windings, bearings, & commutator. The classification of motors can be done with considerations like the type of power source, construction, motion output type, and applications. This article discusses what is a motor winding, types, and its calculation.

Application of enamel coated magnet wire
Wire for winding used in electrical equipment is generally called magnet wire. Simplyput,”enamel coated magnet wire is used for interchanging electrical energy with magnetic energy”.Magnet wires are broadly divided into enamelled wire (coating insulation), coveredconductor wire (fiber/film insulation), and combinations thereof.

Best Price Factory Sale Enameled Copper Coated Aluminum Wire can be used at a working temperature of 180 ClassC. The product has the advantages of direct solderability, good coloring, and low dielectric loss under high frequency. Widely used in windings and wiring of motors, electrical appliances, electronic components, meters, etc.

Application of China Factory Wholesale Copper Pianted Enameled Aluminum Wire
1. High frequency signal transmission
2. The preferred inner conductor material for cable television coaxial cable
3.50 RF cable, flexible RF coaxial cable inner conductor material
4. Leakage cable inner conductive material
5. Computer power supply, other data cable inner conductor material
6. Micro coaxial cable inner conductor material
7. Power transmission
8. Stranded wire
9. Power cable conductor material
10. Control cable inner conductor
11. Special cable inner conductor for automobiles and locomotives
12. Building non-wire conductor materials
13. Conductor materials such as bus bars
14. Fuse
15. Radio frequency shielding network.

Enameled Aluminum Wire Compared To Enameled Copper Wire have some advantages
Aluminum /Copper Wire/foils
Dimension:0.2–10.0mm,
Rectangular: A> 0.8–8mm, B> 2-22.5mm
Square: 0.4*0.4mm–8*8mm
Foils:Thickness：0.2–2.5mm, width:60–1250mm

The voltage resistance performance of enameled wire is mainly affected by several factors:
1. The thickness of the insulating layer, not much nonsense;
2. The degree of aging of the insulating layer and the degree of baking affect the withstand voltage.
3. The quality of the insulation layer is mainly the pinhole performance.

Direct-welding enameled wire is named after its insulating layer uses an insulating material that can be directly destroyed at 360~420¡ã, and it can be directly welded without removing the insulating layer in advance during welding. Direct welding enameled wire is currently widely used in various industries of electromagnetic coils (motors, electroacoustics, inductance, etc.). As for whether it can be used to wind the motor coil, it mainly depends on the motor power or the working environment of the coil, and there is no problem within a certain temperature range.

Enamelled wire stripper is specialized to depainting for transformer and electrical machine etc, and the different strippers can be chose and according to different heat resistance levels and different enamelled materials. The products include BT-112 strong enamelled wire stripper BT-105 quick enamelled wire stripper BT-101A/B stripper etc. Its characteristics BT-112 is applicable to depainting for the thrum of Copper Wire Aluminum Wire with the heat resistance level 180(H), 200(H+), 220(C). BT-105 is applicable to fast depainting for the thrum of enamelled Copper Wire Aluminum Wire with the heat resistance level 130(B), 155(F); BT-101A/B is applicable to depainting for voice coil wire EI.