Anodized Bare Aluminium Wire Strip

The multi-shaped enamel wire refers to a metal wire for winding electromagnetic coils with an insulating paint, also known as electromagnetic wires. The multi-shaped enameled wire is the primary raw material of electrical, motor and household appliances, telecommunications, electronic external electromagnetic windings. In the future, follow the rapid development of industrial appliances, household appliances, telecommunications, electronic products, etc. Market and application fields.

1. Polyester enameled wire (P.E.W.)
Polyester enamel-covered wire is made of heat-resistant Terephthalic Polyester resin as the main grease as the insulating film and baked on the conductor. Its characteristics are as follows:
¡ñThe heat resistance is superior to synthetic tree (P.V.F.) enameled wire and U.E.W. enameled wire.
¡ñExcellent chemical resistance (except alkaline) and solvent resistance.
¡ñThe mechanical strength is comparable to synthetic resin (P.V.F.).
¡ñThe force rate and dielectric rate are comparable to U.E.W. enameled wire.
¡ñAlkali resistance and moisture resistance are better than synthetic resin enameled wire (P.V.F).

For Aromatic polyimide tape-covered aluminum magnet wire, after the aluminum magnet wire is taped with a tape that is 1.5 mm thick with 1.0 mm of this thickness being polyimide film and the remaining 0.5 mm being fluoroplastic, it is heated and heat-sealed.

Axalta today announced that it has reached a final agreement to acquire Anhui Shengran Insulation Materials Co., Ltd. (“Anhui Shengran”). Anhui Shengran is a leading manufacturer of high-quality enameled wire paint in China. Its products are widely used in consumer electronics, electric vehicles and industrial fields. Subject to the conditions of the agreement, the transaction is expected to be completed in the second quarter of 2021. Financial terms have not been disclosed.

ENAMELED ROUND ALUMINUM WINDING WIRES are widely used for Oil-immersed transformer windings, Dry-type transformer, High temperature transformer, Motor, transformer, generator, welding machine; Sealed motor, Power tools motor, Auto alternators motor, Magnet coil, High power motor, household electro motors and micro-motors;

Aluminium Alloy Wires are made from a wide range of aluminum alloys, depending on the customer requirements. Aluminium wires are sold to manufacturers of eyelets, rivets, nails, screws and other various products. Bare Aluminium Wire is used for Cables, Junctions, Rivets, Hangers, Clips and other household Items.

Inductive sensors have outstanding advantages such as simple structure, fast dynamic response, and easy non-contact measurement. They are especially suitable for acids, alkalis, chlorides, organic solvents, liquid CO2, ammonia, PVC powder, ash, oil and water. Liquid level measurement such as interface is currently widely used in metallurgy, petroleum, chemical, coal, cement, food and other industries.

Aluminum bare magnet wire (Anodized Bare Aluminium wire) belongs to the special electromagnetic wire and the insulation layer is the aluminum oxide .Because of no thermal aging phenomenon, it can be used as insulation level of class 220.
The insulation layer of such product is thin, high temperature resistance and insulation performance stability,which is the best choice for low voltage winding wires with producing high temperature, poor environment, heat dissipation difficulty and so on. It can widely be used in electromagnetic industries at home and abroad.

Type of magnetic wire is divided into enameled wire, wrapping wire, insulated wire, combined wires and others,Mainly used in motors, electrical appliances, instruments, transformers, etc., to generate electromagnetic effects by winding coils, and use the principle of electromagnetic induction to achieve the purpose of converting electrical energy to magnetic energy

Thermal Class: 130-220C
Conductor Material: Copper
Standard: IEC,NEMA,GB,JIS
Delivery time: 7-30 Days
Brand Name: LP Magnet Wire
Insulation: PEW, PIW, EIW, AIW, EI/AIW

The current enamel wire industry is relatively low due to the admission threshold, and therefore the production enterprises have more and more, and the market competition is constantly intensified, but in the high-end product field, there are not many companies that can enter, in the present, and future, The enamel wire business wants to achieve better development, and build brands and scale becomes more and more important.

7 type of enameled wire in accordance with insulation materials, list the thermal class, advatanges and application per type of enameled wire. Enameled wire types also can be divided into copper magnet wire and aluminum wire in accordance with conductor.

Fiberglass Covered Insulated rectangular aluminum wire is in accordance with customer requirements in aluminum conductor uniform whole winding package 1-2 layers of alkali-free fiberglass, with the necessary temperature resistance index and compatible adhesive paint dipping and baking process, glass fiber and conductor between bonded into a whole.

Certification: SGS,UL
Size: 0.2mm-8.0mm
Delivery time: 10-30days
Thermal Class: 130-220C
Conductor Material: Copper Clad Aluminum

In theory, any enameled wire can realize the mutual conversion between electric energy, magnetic energy and kinetic energy. However, the use of enameled wire has a processing process, and electrical products also have different working environments. Therefore, in the selection of enameled wire And when substituting, the characteristics of various enameled wires must also be considered.

Paper insulation enameled transposition conductor characteristics:
1. There is no circulating current, the eddy current loss in the coil is small, and the current density can be improved;
2. Simplify the winding process;
3. The full rate is higher than that of the paper-covered wire slot.

Paper-insulated enameled transposed wires are mainly used in the coils of large transformers.

The samples for tensile and thermal shock testing were 3 pieces of 254mm enameled wire.

First pull the enameled wire to the required elongation at a rate of 3.7-4.6 m/sec, then wrap the jerked sample around the mandrel, and then put the wrapped sample into the oven at the specified temperature for 30 minutes. It needs to be suspended in the oven. After leaving the oven, inspect the baked samples for cracking or peeling of the paint film. In this test, the diameter of the mandrel is usually 3 times the diameter of the enameled wire.

The specified temperature of the oven is set according to the temperature specified for the enameled wire of this ANSI Type in the NEMA MW1000 standard, which is usually the temperature grade of the enameled wire +20¡ãC.

The main advantages of fiberglass covered wire are:
1. The quality factor Q value is large;
2. Because it is twisted by multiple enameled wire bundles, it has good flexibility and can reduce the skin effect;
3. Because it is composed of polyurethane enameled wire, the dielectric loss angle is small, and it has direct solderability.
The disadvantage is: poor moisture resistance.

Magnet wire or enameled wire is a copper or aluminium wire coated with a very thin layer of insulation. It is used in the construction of transformers, inductors, motors, generators, speakers, hard disk head actuators, electromagnets, electric guitar pickups and other applications that require tight coils of insulated wire.

A brief introduction to the advantages and disadvantages of copper wire and aluminum wire:Same area:

1, copper wireis large load than aluminum wire . 2, copper wire is more flexible than aluminum wire. 3 copper wire is lower resistivity than aluminum wire. 4,copper wire is more stable than aluminum wire. 5, however, copper wirer price is 3.5 times higher than aluminum wire.

Glass-fiber covered aluminum magnet wire used to have weak coating strength (abrasion resistance, shock resistance, and flexibility). However, that disadvantage has been significantly improved recently by refining material selection and manufacturing methods. The demand for glass-fiber covered aluminum magnet wire is increasing as the wires have excellent uniformity and electrical properties under high temperatures and humidity.

The paint is a process of painting the paint of the enameled wire to form a uniform lacquer layer of a thickness on the metal conductor. This is related to several physical phenomena and painting methods of liquid.

Enameled wire production water also has many uses, and similarly, the requirements for water quality are also different. According to the water quality requirements of the purpose of use, it can be divided into: annealing furnace sealing water, equipment cooling water, lubricant manufacturing water, etc.

Round Enameled Wire is used for transformer coil winding and motor winding, also called electric motor winding wire. And to Measure The Specifications Of Round Enameled Wire is important, include the conductor diameter and insulation diameter.

What is the first thing to make the enamel wire? And the manufacutring process of enameled wire is important, the extruding and baking. And the raw materials: copper conductor or aluminum conductor is enough for client’s requiremnets

Principle: Water molecule (HHO) decomposes water into oxygen and hydrogen through electrolysis. Hydrogen is combustible. Oxygen supports combustion. These two gases are ignited to form a hydrogen-oxygen flame. In layman’s terms, “water turns into fire”

Heat resistance refers to the properties of a substance that can maintain its excellent physical and mechanical properties under heated conditions. The highest use temperature of commonly used materials to characterize. There are different standards and test methods for different materials. Such as plastics are generally expressed by Martin heat-resistant temperature. The coating industry uses a blast constant temperature oven or a high temperature furnace. After it reaches the specified temperature and time, the surface condition of the paint film is inspected, tested, or other properties such as impact, bending, water immersion, salt spray test, etc., and then before and after Test data representation. All coatings used in higher temperature occasions must use heat resistance as an important technical indicator of the coating film

Enamelled wire stripper is specialized to depainting for transformer and electrical machine etc, and the different strippers can be chose and according to different heat resistance levels and different enamelled materials. The products include BT-112 strong enamelled wire stripper BT-105 quick enamelled wire stripper BT-101A/B stripper etc. Its characteristics BT-112 is applicable to depainting for the thrum of Copper Wire Aluminum Wire with the heat resistance level 180(H), 200(H+), 220(C). BT-105 is applicable to fast depainting for the thrum of enamelled Copper Wire Aluminum Wire with the heat resistance level 130(B), 155(F); BT-101A/B is applicable to depainting for voice coil wire EI.

To weld the lead aluminum enameled wire, it is necessary to remove the paint (there are very few household electric fans with very low requirements, and the ballast manufacturer does not remove the paint). The paint removal methods are listed below.
(1) It can be scraped with a blade,
(2) It can be peeled with a centrifugal knife,
(3) The paint can also be rubbed off with a grinding wheel,
(4) Of course paint remover is also available,
(5) You can also use high-temperature tin to burn the paint,
(6) Some people burn with fire
(7) Of course you can also use paint remover to remove paint

Telephone cable is usually thought of only as a communication medium operating at a normal 48 Vdc level. But telephone cable is regularly used by telephone operating companies to supply power to remote telephony equipment such as: PCM (Pulse Code Modulation) repeaters, FDM (Frequency Division Modulation) repeaters, telegraph and various types of control circuits. The normal talk battery voltage is regularly exceeded in the case of long subscriber loops utilizing loop extenders and on dial long line circuits which operate in the 70 to 100 Vdc range. For these applications, the referenced devices are generally current limited to approximately 150 milliamps. In all such cases, normal telephone industry practice usually limits pair-toground applied voltage to 150 Vdc, and pair-to-pair voltage is usually limited to 300 Vdc.